Sleep Cycle Calculator

Find a bedtime or wake-up time that matches your sleep cycles.

I want to…

Enter a target time to see cycle-based bedtimes or wake-up times.

How this sleep cycle calculator works

A sleep cycle calculator maps a target clock time onto 90-minute sleep cycles plus a sleep-onset latency. Choose I want to… as Wake up at… (default) or Fall asleep at…. Enter Hours (0–23) and Minutes (0–59). The headline is the 5-cycle row as HH:MM. The Suggested times table always lists 4, 5, and 6 cycles.

Both Hours and Minutes must be filled numbers. Midnight 0/0 is valid. Empty Hours or empty Minutes shows Enter a target time to see cycle-based bedtimes or wake-up times. Wake up at… subtracts the duration from the wake time to get a bedtime. Fall asleep at… adds the duration to get a wake time. Times wrap around 24 hours.

How to use the sleep cycle calculator

  1. Choose I want to…: Wake up at… if you know when you must get up, or Fall asleep at… if you know when you will go to sleep.
  2. Enter Hours (0–23) and Minutes (0–59). Both fields are required. Midnight is 0 hours and 0 minutes.
  3. Open Cycle settings only to change sleep-onset latency or cycle length. Closing it uses 15 minutes of latency and 90-minute cycles even if different values stay typed. The table still shows 4, 5, and 6 cycles.
  4. Read the headline (the 5-cycle time) and the Suggested times table. Durations are shown as hours to one decimal, such as 7.8 h.

Cycle settings, and closing it

Cycle settings is where you change sleep-onset latency and cycle length. While it is open, those typed values feed the duration. Closing it uses 15 minutes of latency and 90-minute cycles even if different numbers stay in the fields. While the section is open, empty latency is treated as 0 minutes, and empty or 0 cycle length falls back to 90.

Sleep-cycle formulas

Duration is latency plus the cycle count times cycle length, in minutes. Wake-up mode subtracts that duration from the target; fall-asleep mode adds it. Negative or over-24-hour results wrap with modulo 1440 minutes.

Sleep duration
duration=latency+cycles×cycle length
Bedtime from a wake-up target
sleep time=wake time−duration

Fall asleep at… uses wake time = sleep time + duration. The table always uses 4, 5, and 6 for cycles. The headline is the 5-cycle row.

Worked examples

Example: wake at 06:30, latency 15, cycle 90

Five cycles last 15 + 5 × 90 = 465 minutes (7.8 h in the table). 06:30 minus 465 minutes is 22:45. Four cycles (6.3 h) land at 00:15. Six cycles (9.3 h) land at 21:15. The headline is 22:45.

Example: fall asleep at 22:45, same settings

Adding 465 minutes to 22:45 wraps to 06:30. The headline is 06:30, and the table still lists 4, 5, and 6 cycles.

Example: empty latency, cycle length 80, wake at 07:00

Open Cycle settings, clear latency, and set cycle length to 80. While the section is open, empty latency is 0, so five cycles last 400 minutes and 07:00 minus 400 minutes is 00:20. Close Cycle settings and the duration uses 15 and 90 again, even if 80 stays typed: five cycles are 465 minutes, and 07:00 minus 465 minutes is 23:15.

Things to keep in mind

Real sleep cycles vary by person and night. These times are a schedule guide, not a guarantee of lighter wakings. Waking near the end of a cycle may feel easier because it avoids interrupting deep sleep. This is not medical advice.

Sleep cycle calculator FAQ

Which fields are required?

Hours (0–23) and Minutes (0–59) must both be filled. Either empty shows Enter a target time to see cycle-based bedtimes or wake-up times. Midnight 0/0 is a valid target.

Does closing Cycle settings ignore latency and cycle length?

Yes. Closing Cycle settings uses 15 minutes of latency and 90-minute cycles, even if different values stay typed. Open it again to use your numbers. While it is open, empty latency is 0, and empty or 0 cycle length falls back to 90.

Why is the headline always the 5-cycle time?

The widget always prints 4, 5, and 6 cycles in Suggested times. The large result is the 5-cycle row as HH:MM.

How are durations shown in the table?

Sleep minutes ÷ 60, formatted to one decimal with h, for example 7.8 h for 465 minutes.

Do times wrap past midnight?

Yes. Adding or subtracting duration uses modulo 1440 minutes, so 06:30 minus 465 minutes is 22:45 the previous evening.

Does this sleep cycle calculator store my numbers?

Completed results can be saved in this browser’s local history so you can reopen them later. They stay on your device and are not sent to our servers or to analytics.